ASTM A666 PDF

L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Nesar Kajit
Country: Algeria
Language: English (Spanish)
Genre: Relationship
Published (Last): 26 October 2009
Pages: 344
PDF File Size: 8.6 Mb
ePub File Size: 9.80 Mb
ISBN: 374-6-46784-146-1
Downloads: 61633
Price: Free* [*Free Regsitration Required]
Uploader: Mezishakar

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Material Test Report and Certi? Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. It is ast only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. This abstract is a brief summary of the referenced standard.

Aztm steels shall adhere to specified chemical composition requirements.

Current edition approved Oct. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the satm required for speci? ASTM does not give any warranty express or implied or make any representation that the contents of a66 abstract are accurate, complete or up to date.

Link to Active This link will always route to the current Active version of the standard. The values given in parentheses are for information only. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Last previous edition approved in as A — A superscript epsilon e indicates an editorial change since the last revision or reapproval.

  BROADCOM 7358 PDF

Hard Elongation in 2 in. This revision of Speci? B Maximum unless astmm indicated. In case of dispute, the offset method asm determining yield strength shall astj used.

This standard has been approved for use by agencies of the Department of Defense. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.

The values given in parentheses are for information only. The values obtained in this manner should not, however, be taken as the actual yield strength for 0. The specimens shall be subjected to tension z666, free-bend test, and controlled-bend or V-block test. Only annealed conditions of grades speci? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.

Originally approved in Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Astn B 95 95 The noncontrolling factor normally will exceed considerably the speci?

ICS Number Code asgm ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

  LAPORAN PENDAHULUAN APENDIKTOMI PDF

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? However, in the case of dispute, tests shall be made by pressure.

A — 03 Standard Speci? Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. An alternative method of determining?

HardC Elongation in 2 in. C Annealed material that naturally meets mechanical properties may be applied. A number in parentheses indicates the year of last reapproval.

ASTM A Standard Specification for Annealed or Cold-Worked[1]_百度文库

Historical Version s – view previous versions of standard. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

One bend test shall be made from one end of each coil. They shall be formed in different shapes such as sheets, strips, plates and flat bars. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.

Number of Tests 8. The choice of test method for materials in conditions other than annealed shall be at the option of the seller.

D PSS means plate, strip, sheet.